This manual describes the S700 (701-724) series of digital servo amplifiers. Includes general safety information, approvals, packaging, technical specifications, mechanical and electrical installation, setup, expansion cards, and troubleshooting.

This manual describes the S748-S772 series of digital servo amplifiers. Includes general safety information, approvals, packaging, technical specifications, mechanical and electrical installation, setup, expansion cards, and troubleshooting.

This manual describes the S700 series (701-724) of digital servo amplifiers. Includes general safety information, approvals, packaging, technical specifications, mechanical and electrical installation, setup, expansion cards, and troubleshooting.

This document defines the AKM2G servo motor torque characteristic versus speed as graphs for each variant and model. These speed/torque performance curves will assist in motor sizing and selection for a given application.

This document defines the AKM2G servo motor torque characteristic versus speed as graphs for each variant and model. These speed/torque performance curves will assist in motor sizing and selection for a given application.

REACH SVHC Certification.

EU RoHS Declaration for KBM.

QMP-SynqNet datasheet providing key benefits and specifications.

This manual describes the AKM2G synchronous servomotor in Deutsch, English, Italiano, Espanol, Francais, and Русский. Provides information regarding safety, standards, handling, packaging, technical descriptions, mechanical and electrical installation.

EU Declaration of Conformity for mains filters (1NF-10, 1NF-12, 1NF-20, 1NF-25, 3NF-07, 3NF-16, 3NF-30)

Circuit and Dimension drawing of the 3NF-30 Mains Filter.

Circuit and Dimensions drawing of the 3NF-16 Mains Filter.

Circuit and Dimension drawing of the 3NF-07 Mains Filter.

Circuit and Dimension drawing of the 1NF-25 Mains Filter

Circuit and Dimensions drawing of the 1NF-20 Mains Filter

Circuits and Dimensions drawing of the 1NF-12 Mains Filter

Circuit and Dimensions diagram of the 1NF-10 Mains Filter.

S200 Base and SynqNet Installation Manual

For drives with increased Memory size only, from Hardware Revision 2.30. Do not load to former drive versions. EN: Release of FW 6.07 for S700 (HW 2.3, 1 STO and 2 STO, all high-current). This firmware replaces the previous standard version 6.01. Changes in this version:
Motor Support
- support for motors with MPOLES>= 172 (this MPOLES setting was not possible because of MSPEED/SLJSWITCH deadlock).
- Function for motor inductivity measurement (CALCML)
- CALCHALL function implemented (testing of hall/motor assignment).
- Support for motor data base 1.46 (AKM2G)
Feedback support
- VCOMM limit value extended to 25000 RPM
- ramp function (ACCR) for analog position command (ANCNFG=8)
- HDSL: Software reset for F04 implemented
Fieldbus
- PLL command can be accessed via Object Number 1057
- PROFIBUS: CONTINUE problem fixed (no automatically start of motion task after HALT OFF fixed)
- Support for BISS-C multiturn implemented. BISSREVOL defines number of multiturn bits.
- Pllhub is used not only for EtherCat but also for CAN and Aquarius
- (only Synqnet,Sercos and Sigmatek are using constant value 2 instead of PLLHUB)
- EtherCat: EIOBUF command for EtherCat mapping values implemented. DRIVE Bit 0x2000 reports support for CALCML and EIOBUF for the DriveGUI.
Safety
- SFD3 problem at switch on with DIR=20 and Safety card (error F31o19i02) fixed.

Firmware for S300 drives. SFD3, HDSL support. For drives with increased Memory size only, from Hardware Revision 4.20. Do not load to former drive versions.