下载
标题 | 版本 | 文件语言 | 发布日期 | Category | 旧版本 |
---|---|---|---|---|---|
Legacy - SEPLink Software - v.2.0.2 - for Servostar S, CD, Pico, and other Servotronix products, alternative to MotionLink - This software runs on Windows XP, and has not been officially tested on newer Windows versions. |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - Servostar S and CD AKM Encoder Based System Datasheet - connection diagrams and drive settings |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - Sizing IDC Actuators and Electric Cylinders - This also applies to non-IDC applications. |
发布版本: – |
English | Application Notes | 查看全部 | |
Legacy - Wire Pinout for AKM with Commutating Encoder to B8000 |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - Motor Configuration Files for BK and B8000 Series - Application Note explaining the BK motor files. |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - Loading Configuration File for B8961 & B8962 - How to load a motor file into the B8961 and B8962 using Servo Tuner. This is only needed if the motor file is not contained in the drive firmware. |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - B Series to BK Series IDC Motor Conversion |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - BK to B8000 cable Diagram |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - BK23 Lead Wire Pinout Application Note - Pinout for BK motor (AKM23D) connection to B8000 series drives. (B8000 and BK23 combination is not recommended. Motor failure is likely to occur.) |
发布版本: – |
English | Documentation | 查看全部 | |
Legacy - B8000 Motor Files for BK & AKM Motors - These are the default motor configuration files for the B8001 and B8501 drives. (Do NOT use the BK23 (AKM23D) motor with the B8000 Series drives. Motor failure is likely.) |
发布版本: – |
English | Software | 查看全部 | |
T12 (IDC) Stepper Motor Wiring Application Note |
发布版本: – |
English | Documentation | 查看全部 | |
Basic Motor Theory of Permanent Magnet DC Motors |
发布版本: 01/01/2004 |
English | Documentation | 查看全部 | |
Legacy - Quickset Software for IDC B8000 Series Servo Drives - Quickset is a revision of Servo Tuner that was made to run on Windows XP . It has not been tested on Windows 7. |
发布版本: 4.2.48 |
English | Software | 查看全部 | |
DS6 Catalog Data Sheet |
发布版本: – |
English | Documentation | 查看全部 | |
DS6 Roll Moment Deflection Calculator - Spreadsheet for calculating an estimated deflection based on a roll moment load |
发布版本: – |
English | Calculator | 查看全部 | |
DS6 Deflection Spec Sheet - This shows the deflection a specific loading. |
发布版本: – |
English | Documentation | 查看全部 | |
DS4 Series Positioning Tables User's Manual |
发布版本: – |
English | Documentation | 查看全部 | |
DS4 Payload Calculator - Calculates travel life based on loading |
发布版本: – |
English | Calculator | 查看全部 | |
DS4 Deflection Spec Sheet - This shows deflection at specific loads. |
发布版本: – |
English | Documentation | 查看全部 | |
DS4 Limit Sensor with S300 Application Note - Explains how to connect the DS4 limit sensors with the S300/S600/S700 servo drives. |
发布版本: – |
English | Documentation | 查看全部 |